(3) Cherry Burrell 6,000 Gal. S/S Refrigerated S/S Silos, S/N E-065-91, S/N E-340-88 and S/N E-339-88 – Complete with Vertical Agitators, Sprayballs, Tri-Clover Air Valves with Mounted Accumulators
 
Mueller 20,000 Gal. Jacketed S/S Silo, Uninstalled & Ready to Load

1997 Seitz 3,000 Gal. S/S Dome-Top Cone Bottom Processor, S/N S97-8287-3, 150 psi @ 300 Degree F – Complete with Bottom and Side Sweep Scrape Surface Agitation (Outside Dia. - Approx. 124” W x 142” H to Top of Tank)
 
(2) APV 2,000 Gal. Dome-Top Cone-Bottom S/S Processors, S/N E6916 (Tank #S246(#1) and S/N E6915 (Tank # ST247(#2) (1987) 75 psi @ 350 (Tank #S246(#1) – Complete with Bottom and Side Sweep Agitation, Dual Sprayballs, Side Man Door, Tri-Clover Air Valve (Inside Dia. 83” W x 82” H) (Outside Dia. 89” W x 140” H)
 
(2) APV 1,500 Gal. Dome-Top Cone-Bottom S/S Processors, S/N E0704 and S/N E0703 – Complete with Bottom Side Sweep Scrape Surface Agitator, Baffle and Dual Sprayball (Inside Dia. 84” W x 56” H), sq.ft. Surface 110

Walker 1,500 Gal. Dome-Top Cone-Bottom S/S Processor, Model PZ-CB, S/N 1867 – Complete with Bottom Side Sweep Scrape Surface Agitator, Baffle and Dual Sprayball (Inside Dia. 62” H x 82” W)
 
(2) Cherry Burrell 1,500 Gal. Dome-Top S/S Processors, Model MEPDA, S/N 1500-73-1911 and S/N 1500-73-1910 with Bottom Sweep Agitation, Baffle, Dual Sprayballs, Mettler Toledo Type 2100E Digital pH Meters

Tank Auxiliaries including: S/S Tank Walk Platform – 21 ft. L x 28” W x 7 ft. H with Handrail, Stairs, Support Structure
 
(2) 800 Gal. Jacketed Hinged Lid S/S Mix Tanks (70” W x 36” Deep)

Breddo 100 Gal. S/S Likwifier, Model LDS100, S/N D6829892357 – Complete with Offset 15 hp Motor and Tri-Clover Air Valve

(2) APV S/S Ribbon Blenders, S/N G-9752 and G-9751 (37” W x 35” W x 37” Deep) with Hydraulic Systems, Lids, Air Valves and Operators Platform (Used for Processing Sour Cream and Dips)

Westfalia 55,000 lbs. per hour CIP Cream Separator, Type MSB200-01-076, S/N 1674009 with Valves, Controls and Tools with 2006 Upgrade Including Direct Drive with Allen Bradley Frequency Controller
 
Westfalia 35,000 lbs. per hour CIP Clarifier, Type MSA40-06-076, S/N 1624573 with Valves, Controls and Tools
Separator Spare Parts Including: Spare Motor, Clutch and Related Parts

APV 55,000 lbs. per hour HTST System with Press, Model R51, S/N 14557 (Set-Up with Skim & Cream Joint System) – Complete with (6) Dividers, (206) Plates, (2) Tri-Clover Flow Diversion Valves, 3” Nested Holding Tube, Balance Tanks, Foxboro Flow Meter, APV Positive Pump, (2) Centrifugal Pumps – 5 hp and 20 hp; Tri-Clover Air Valves; Installed Piping with Controls; Allen Bradley SLC500 PLC Controls with Panelmate Display; Bell and Gossett Shell and Tube Heat Exchanger
Gaulin 3-Piston 2-Stage Homogenizer, Model K

(3) Kusel 4,500 Gal. Cottage Cheese Vats, Model 348038CCESA, S/N 0103659 (Inside Dia. 80” W x 32 ft. 8” L x 33” Deep); Model 348538CCESA, S/N 1094324 (Inside Dia. 80” W x 32 ft. 8” L x 33” Deep) and S/N 1094314 (Inside Dia. 80” W x 32 ft. 8” L x 37” Deep) (Outside Dia. 34 ft. x 85” W) – Complete with Elips-E-Stir Agitation and Allen Bradley SLC500 PLC Controls, Magnatek and Variable Speed Controllers, as new as 2002

2007 Maxco ME-24 Box Former/Sealer, S/N BB0801 – Complete with Nordson ProBlue 10 Gluer and Allen Bradley Micrologixs 1200 PLC Controller and Extensive New Conveyor System
McDowell Case Former/Sealer, Model 201RH, S/N 1291721 with Nordson 2302 Gluer
(2) Little David Adjustable Case Sealers, Model LD72, S/N 330569837 with Marsh Ink Jet Coders

Pryor 3 lb. to 5 lb. All Stainless Culture Products Filler with Tamper Evident Sealer, Lid Inserter and Cup Dispenser

Late Model Overhead Case Handling System – Complete with 10 ft. L Case Washer Mounted on All S/S Platform All S/S Construction, 275 ft. L Overhead, 14” W Pan, (5) Cannon S/S Case Inverters, Lane Diverters, Pneumatic Gates, Straight Sections and Bends, Cable, Drive, Also including 70 ft. Above Ground Round About Case Conveyor System with S/S Pan, Chain, 30 hp Cannon Drive, Lane Stop and Take-Up
Hytrol Conveyor System including: Over 300 ft. L x Most Sections 17” W Above Ground and Overhead – Complete with Pack On and Pack Off Stations, Straight Sections, Bends, Drives, (2) 12 ft. 8” H Elevator Systems including 9 ft. 5-Tier Spiral Conveyor System
S/S Product Conveyor including: Large Assortment Descon S/S Product Conveyor, Sizes including 3-1/4” to 7-1/2” W with SEW Drives, Straight and Long Sections, S/S Leg Supports, Some Sections Very Late Model

(2) Video Jet Ink Jet Coders, Model Excel/170i/AF, S/N 060341040WD and S/N 032910006WD
 
(2) Additional Diagraph Ink Jet Coders System

Over (10) Centrifugal Pumps including: New Ampco 5 hp, Model KC2 with 2-1/2” x 2” Head; Various Tri-Clover ¾ hp to 10 hp, Model C228, C114 and C216 & Other’s
(7) Positive Displacement Pumps including: (2) Waukesha Model 130 with Drives, 3” Clamp Type Heads, Mounted on Stainless Frame; (2) Waukesha Size 25 Pump Head; APV Model R3BS and R3TS 2” Clamp Type Head with Drive; Crepaco Size 4 with 2” Clamp Type Head Drive on Stainless Frame
(3) Sine Pumps including: Sine Pump with 2” Clamp Type Head with Variable Speed Drive with S/S Base; Sine Pump with 3” Clamp Type Head, Model MR135-NNTC & SEW Drive; Sine Pump with 3” Clamp Type Head, Model MR135 with Drive Mounted on Stainless Frame
S/S Piping including: Large Assortment 2” to 2-1/2” S/S Piping including Some New Pipe Inventory, Also including Sanitary Fittings with S/S Clamps, Elbows, Reducers, T’s, Caps, Nuts and More
Valves including: Over (20) Tri-Clover 2” and 2-1/2” Most Clamp Type Air Valves; Plug Valves, Butterfly Valves, Alfa Laval 2-1/2” 3-Valve Air Valve Cluster; Accurate 2” Clamp Type Flow Meter; Tri Clover Air Valve Clusters including: (3) 2” 2-Valve; (2) 2” 4-Valve; (2) 2” 8-Valve; 2” 12-Valve; 2-1/2” 5-Valve and 3” 4-Valve Clusters

Plant Controls Including: Cabinet with Allen Bradley PLC 5/80 PLC with Remote and Panelmate Display & Other Assorted Control Panels

Vilter 6-Cylinder 75 hp Ammonia Compressor, Type 446, Size 4585A, S/N RCB902632 with Updated Baldor 75 hp Motor
 
(3) Mycom 4-Cylinder 75 hp Reciprocating Ammonia Compressors, (2) Model N4B, S/N 19893 and 20509 and (1) Model N4WB, S/N M430062 with Starters and (1) Baldor Motor Updated
Frick 4-Cylinder 50 hp Vertical Ammonia Compressor, Type 7, S/N 49383
Frick Condenser, Model AFC290, S/N AF79032.

Additional Ammonia Components including: E.L. Nickell 152” L x 40” W Vertical Ammonia Receiver ; 150” L x53” W Horizontal Ammonia Receiver/Circulating System with Circulating Pumps including: Hansen Auto Purger, Model APC, S/N N2609; Ammonia Control Panel Complete with Allen Bradley 5/60 PLC Controller with Panelmate Touch Display
 
(2) No-Frost Systems with (2) Niagara Floor Standing Dehumidifier/Blower Units, Model A6213J, S/N 40752 and S/N 40753, Operating on Ammonia with Accumulators, Pumps and Controls (140” W x 12 ft. Deep x 198” H ) including Concentrator, Model 90003, S/N 05-18001 with APV Plate Press with Controls
 
King Air Handling Unit, Model C2015-95, S/N 91-Y-2237-A, Steam 1,296,000 lbs., R717 Refrigerant, 50-Ton
 
(2) Scott Air Pack Breathing Apparatus

Sullair 125 hp Screw Air Compressor, Model 20-125H, S/N 003-590-51, 125/135 psi with Saftronics Starters
 
Pac-Air Ingersoll Rand 75 hp Screw Air Compressor, Model PA75, S/N P1825U74858 with Saftronics Starters
 
Sullair 30 hp Screw Air Compressor, Model 10B-30WC, S/N 003-67124, 115/125 psi
Air Compressor Support Items including: Miller-Bilt Compressed Air Dryer, Model JW1210HLL

Nissan 4,300 lb. Propane Forklift, Model CPF02, S/N 022541 with 3-Stage Mast and 169” Reach
 
Raymond 3,000 lb. 36-Volt Stand-Up Electric Forklift, Model R30-C30QM, S/N R30-03-05700 with 4-Stage Mast, 220” Reach, Side Shift and Ferro V Charger
 
Raymond 3,000 lb. 36-Volt Stand-Up Electric Forklift, Model EASI, S/N EZA-93-00397 with 2-Stage Mast, 206” Reach

Raymond 3,000 lb. 24-Volt Stand-Up Electric Forklift, Model EASI, S/N ET-B-95-02362 with 2-Stage Mast, 177” Reach and Ferro V Charger

Big Joe 3,000 lb. Walk-Behind Electric Forklift, Model 350557 with Charger and 106” Reach
 
(3) Yale Electric Pallet Jacks
 
Battery Service Carts
 
Forklift Accessories including: Hercules Manlift Platform
 
C & M Hydraulic Cardboard Baler – 58” W x 70” W x 90” H
 
2003 Rudco Trash Compactor, Model RP-3000, S/N 2925 with Container and Hydraulic Pump (Footprint 23 ft. 5” L x 8 ft. W x 102” H)

14-Sections 2-Deep x 2-High Pallet Racking with 14’ High Uprights, 41” W Pallet with Top Mounted Mezzanine Platform with Stairs and Louisville Aluminum Stage
 
16-Sections 3-High x 12 ft. H Uprights Standard Pallet Racking
 
Other Additional Pallet Racking Available.

OTC 4,000 lb. Portable Boom; Grizzley Pedestal Drill Press, Model G7947; Milwaukee and Bosch Rotary Hammers; Portable Burning Cart; Double End Grinders; Milwaukee and DeWalt Drills; Vacuum Pump; (2) Lincoln Idealarc Arc Welders; Hydraulic Press; Snap-On Plasma Cutting System; Walker Turner Vertical Drill Press; 44 Vertical Belt Sander; Come-A-Longs; Lifting Straps; Pullers; Bearing Press Tools; 12” Rotary Sander; Cub Cadet Gas 26” Power Snow Blower; Wallace 14” Chop Saw; Ridgid Model 1224 Pipe Threader with Vise and Dies; Genie Lift; Parts Washer; Flammable Storage Cabinets; Parts Shelving; Motorola Radius SP50 2-Way Radios; Portable Tool Box; Steel Table with Vise; Air Tools including: Black Patriot 1-1/2” Impact Wrench; (3) Chicago Pneumatic ½” and ¾” Impact Wrenches and Other Air Tools; Hand Tools including: Sockets, Large Assortment of Wrenches, Hammers, Levels, Pipe Wrenches, Hydraulic Jacks, Porta-Power Kit, Greenlee Pipe Bender, Etc.

Large Assortment of Spare Parts for Most Machines including: Separator Parts; Tank Parts; HTST Parts; Centrifugal Pump Parts for Tri-Clover and Others; Large Assortment Sanitary Valve Parts including: Air Valves, Butterfly Valves, Elbows, T’s, Ferrules; Drive Parts including: Chain Inventory; Sprockets; Couplers; V-Belts; Assortment of Timken, Fafnir, MRC and Other Bearing Inventory; Allen Bradley and Other Variable Speed Drives; Allen Bradley PLC Components; Anderson Pressure Sensors and Other Instrumentations; Strahman Parts; Foxboro Flow Meter Parts; Electrical Supplies including: Condulets; Condulet Fittings; Various Wiring; Starter Boxes; Breakers; Fuse Supply; Heater Elements; Etc.; Assortment of New and Used Motors and Drives; Plumbing including: Assortment Brass and Other Valves; Chemical Feed Components including: Wilden Pump Parts; Filter; Etc.; Hardware Bins with Hardware; Sanitary Gaskets; Plastic Conveyor Chain; Casters; New Eco Lab Wall Mounted Boot Sanitizer; Various Sized Steel and S/S Plumbing Fittings including: Elbows, T’s, Reducers, Nipples with Piping; Pipe Rack with Pipe Inventory including: Copper, All Thread PVC, Aluminum and S/S Channel, Box Tubing

(2) 2008 Bishamon 3,000 lbs. 43” Scissorlift Platforms, Model EZ30; Weigh-Tronix 10,000 lb. Platform Scale, Model WI-125LED, S/N 40034 with Digital Read-Out – 5’ x 4’ All Stainless Platform; Weigh-Tronix 100 lb. Platform Scale, Model WI-125 with 20” x 20” Platform; (7) Weigh-Tronix 12 lb. Platform Scales, Model QC-3265 with 9” x 9” Platform; (3) Better Pack Tape Sealers; Portable Louisville Step Ladders; Louisville Portable Stairs; Hydraulic Pallet Jacks; 138” L x 36” W Dual Compartment S/S Wash Trough; (2) Tanker Sprayballs; 2-Compartment Wash Sink; 50”, 75” and 78” Jet Spray Wash Troughs with Tri-Clover Pumps; (2) Klenzade Model T Jr. Portable Foamers; Assorted S/S Stands with Plastic Grating (Assorted Sized); Stainless Tables; Rubbermaid Carts; Drum Containments; Small S/S Tanks; Lab Items including: Garver Centrifuge; CEM AVC80 Microwave; Incubator and More

Aqua-Aerobic Systems Waste Water System Complete with 148,000 Gal. Sludge Tank, 411,812 SBR Tank, 57,092 Gal. Settling Tank, A.O. Smith 10,100 Gal. Equalization Tank S/N 8920279- (All Tanks with Bolted Construction), (2) Justin 25,333 Gal. Vertical Fiberglass Tanks, (3) Aerzen 75 hp Rotary Blower Units, Type AMUSAGM50L-00 with New Arzen 8” Rotary Blower Head, Model GM501, Aeration Pumps, Valves, Piping , Complete with Allen Bradley SLC5/02 PLC Controls, Call for Details!!!
 
Waste Water Lab including: Grieve Laboratory Oven; Ohaus Analytical Digital Scale, Model AS120; Micro Master 4-Optic Microscope; Hach DR 30000 Spectrophotometer; Hach COD Reactor; (2) YSI 518 Oxygen Meters

1982 GMC V-8 7000 Box Truck, VIN #1GDG7D1B7CV568749 – Complete with Gas Engine, 5-Speed Transmission, 18 ft. Body and Dual Axle (121,000 Miles)

Additional Items including: (2) Shell and Tube Heat Exchangers; Hytrol Conveyor Sections; S/S Product Conveyor Sections; Pallet Racking Components; Control Boxes; Hyster Propane Forklift; Box Former/Tape Sealer; (2) Surge Tanks; Tank Agitator; (3) Drives; Haab Pneumatic Caser and Additional Caser; Balance Tanks; S/S Round Accumulation Table; Waukesha Size 55 Positive Pump (Check Back for Details!)